Відео

Even some used ones come with a little seat with the third wheel.

Thank you very much. I see now that the link stopped working here it is: www.manualslib.com/manual/925112/Behringer-Xr18-Xair.html?page=8#manual

Oh, you mean the rubber contacts under the keybed? those went off with fingers

Hi. Those parts were available at Korg Parts at www.partsisparts.net/catalog/korg-parts But the keyboard is now old, so the part may be discontinued...

For this matter, you should refer to github

Pozdrav. Hvala na pitanju. Na 3:00 minuti videa se vidi shema spoja. za stanicu se koristi lijeva senzor ploča, plava, zelena i crna žica. plava je ch2 - skretanje, zelena je ch1 - gas i crna je minus

Nevermind it looks like you weren't wearing a strap. Thanks for the video

Yeah... no strap.. although, I never got shocked, I would advise to get a ground strap for a few bucks...

@@snowkingcro Thanks for responding. I was more worried about destroying the motherboard components.

I see, well, either way, it's on you to choose ☺️

Thanks :)

Hvala. Kvarcni pijesak bi bio bolja opcija, ali u videu je čisti cement (pomješan sa vlaknima i bojom za beton u prahu). Više sam se bazirao na kalup i testiranje koliko često se može koristiti prije nego izgubi oblik i svojstvo kalupa...

Contact spray

I worked on three models, everyone's different. Generic china motherboard... but I figured, the cheaper ones have less parts and sometimes are harder to program

Yeah, that's the way to do it :)

I think the same as mine... the reflector fell off... anyway, CAUTION should be your best friend

about 15$ maybe

It could be a bad screen?

Contact spray... contact cleaner, and so on...

Here you go github.com/snowkingcro/hoverboard-firmware-hack-esk8

Here is the Link to the Transmiter and receiver: shorturl.at/ayCM7 The wiring diagram is on 2:50 just use wires for left sensor board

@@snowkingcro thank yu plise controler rc transmiter hoverboard maintboard wiring diagram?

that depends on the rc transmitter

Here is the Link to the Transmiter and receiver: shorturl.at/ayCM7 The wiring diagram is on the tutorial video - ua-cam.com/video/2Zg-sp9BD_g/v-deo.html on 2:50 just use wires for left sensor board

@@snowkingcro thank yu custom firmware dowloadlink? government?

github.com/snowkingcro/hoverboard-firmware-hack-esk8

Have you tried Ebay

Hi there. Did you see my video of the final hover mover? ua-cam.com/video/d5Pv82Sy5zc/v-deo.html I left the link to the firmware there.

My friend, you can pay attention to our 【ER-102】 in-ear monitor system with bluetooth audio playback and signal transmission range up to 300m

is there a link?

@@snowkingcro ua-cam.com/video/cbPFWq73ps8/v-deo.html

Thank you

Na ovom videu ua-cam.com/video/2Zg-sp9BD_g/v-deo.html na 2:54 je slika, koju treba pauzirati. Transmiter je spojen na LEFT SENSOR BOARD

On this video, look in the comments, there is the link to the Firmware

I'm pretty Sure the method is very similar

Well, it isn't so bad that you could not use it, but it's not as clear as it should be... but gets the job done :)

They tend to be warm but I had no problems whatsoever. It works aprox. one hour per moving, so... it gets warm, but thats it... I can hold to the wheel with my hands

They tend to be warm but I had no problems whatsoever. It works aprox. one hour per moving, so... it gets warm, but thats it... I can hold to the wheel with my hands

Apple has this pretty much sorted with bluetooth channeling and ble midi

Exactly

Hi. Even if i would, the shipping would be a bigger problem

@@snowkingcro i can imagine, nowadays the shippingbill is extreme expensive, and even more if it's from USA to Germany.

About 15$

No, I didn't, but if you get the backfeed, i'd use some diodes to prevent the power going the wrong direction

Well, I bought some sensors to implement with an arduino board, but i'm stuck due the lack of free time :/

Do you mean the cables on the Hall sensor? No, not at all, just keeping the wires short

hm, želiš upravljati hoverboardom kao ja na mom videu? Pa, morat ćeš flashati firmware od hoverboarda sa firmverom u linku ispod videa... ali upamti da je to nepovratan proces, pa ako to napraviš, nećeš ga više moći vratiti na funkciju hoverboarda

Yeah, it kinda sucks, but, for a small band, without a van, or any ability to use wedges or stage monitors, it gets the job done... I just think that I should bought the other version with higher frequencies... the sound would maybe be clearer...

Yeah, and buy the expensive one.

Keep the cables short... if you make them long, you get stuttering and stuff that gets you only mad

No, they are USB powered, so only usb

Shure

Always disconnect the battery first.

pretty much only the design...

Yes, You can see it here : ua-cam.com/video/Ww_59NLo0_o/v-deo.html

@@snowkingcro Can you tell me the wiring for the steering, i cant seem to find any answers on the internet. Thank you :)

Did you use the hex file for flashing?